bonding strength
基本解釋
- [紙] 結合強度；粘接強度；黏合強度
英漢例句
- The high-strength bonding between diamond grit and steel matrices was realized by using a Ti-based filler alloy under controlled brazing conditions.
采用鈦基合金釬料，適當控制釬焊工藝，實現了金剛石與鋼基體的高強度連接。 - With the constant high-temperature bonding-agent, the relationship was introduced between the quantity of bonding-agent and strength, porosity, porous diameter, infiltration.
主要研究了高溫粘結劑的加入量對制品的強度、平均孔徑、孔隙率、滲透性等性能的影響。 - The results show that there is not any evidence of silver migration within LTCC construction, and conductor adhesive force, wire-bonding strength and insulation resistance are high.
結果表明：基板內部的銀導體不存在遷移現象，導體的附著力、鍵合強度以及基板的絕緣電阻等性能均比較理想。
lib.nwnu.edu.cn
雙語例句
詞組短語
- bonding g strength 膠合強度;膠接強度
- bonding bending strength 黏結抗折強度
- Bonding Media Strength 膠粘介質強度測量
- bonding -strength 結合強度
- shearing -bonding-strength 剪切膠合強度
短語
專業釋義
- 結合強度
The results show that:the coating hasa unique with Vickers micro-hardness of 1 134HV0.1 and bonding strength more than 64 MPa.
結果表明:該涂層具有獨特的顯微組織結構;涂層的維氏顯微硬度達到了1 134HV0.1;結合強度超過64 MPa。 - 粘結強度
After gaining the best activation patterns and the best content of coal gangue in cement mortar,the flexural strength ,compressive strength, bonding strength and consistency of the mortar were tested after adding fibrous brucite and water-reducing agent.
在獲得了煤矸石在水泥砂漿中最佳活化方式和最佳摻量后,在原摻煤矸石普通砂漿的基礎上摻入水鎂石纖維及減水劑進行不同灰矸比和不同灰砂比的水泥砂漿試驗,除了抗折抗壓強度測試外,還測試了砂漿的粘結強度和稠度。 - 粘接強度
In this paper, a silver-epoxy adhesive die-attachment for experiment was prepared. Various experiment conditions for optimal bonding strength of the die-attachment were investigated by shear-mode experiments.
制備了用于試驗研究的銀導電膠互聯的基板-芯片試樣,通過剪切模式破壞試驗,研究了為獲得銀導電膠的最佳粘接強度的各種試驗條件。醫藥科學
- 粘接強度
The main method which judges whether an adhesive system works or not is the bonding strength test.
粘接強度測試是評價一種牙本質粘接系統性能的重要方法。 - 粘結強度
The shear bonding strength showed no significant difference between two groups,which met the clinical requirement.
同時兩組牙齒間托槽的抗剪粘結強度沒有顯著的差異性,且都能滿足正畸臨床應用中對托槽抗剪粘結強度的要求。機械工程
- 結合強度
Culcination temperature and time influence the self-generated oxide layer, and then act on the coating’s quality and bonding strength.
煅燒溫度和時間通過對自生氧化層的作用影響涂層質量和結合強度。 - 膠合強度
So did the 5-ply panels. Bonding tests showed that compressing method could improve 5% of panels’ bonding strength and percentage of wood failure.
剪切實驗表明，膠合板的膠合強度和木破率都由于單板的壓縮均提高了5％左右。 - 膠合性能
- 膠合強度
When the temperature is 140°C, the bonding strength is 1.65MPa, which meets to the requirement of I-plywood.
熱壓溫度為140℃時，膠合強度為1.65MPa，達到Ⅰ類膠合板膠合強度要求。 - 附著力
By modeling, the formulas for calculating the line peel-off intensity and the plane peel-off intensity were deduced, and the standard to estimate the bonding strength was put forward.
最先引入了線剝離強度和面剝離強度兩個附著力性能評價參數,通過建模推導出計算公式,從而給出了附著力檢測評價標準。土木建筑工程
- 黏結強度
- 鍵合強度
That defects are mainly in interface of SDB affects bonding strength.
硅鍵合片的缺陷主要集中在鍵合界面,鍵合強度受到很大影響。物理學
- 粘合強度
- 粘合強力
- 黏結強度
- 粘合強度
- 黏結強度
- 黏合強度